Search:
Computing and Library Services - delivering an inspiring information environment

Thermal parameter optimisation for accurate finite element based on simulation of machine tools

Abuaniza, Ayman (2015) Thermal parameter optimisation for accurate finite element based on simulation of machine tools. Doctoral thesis, University of Huddersfield.

[img] PDF - Accepted Version
Restricted to Repository staff only until May 2018.
Available under License Creative Commons Attribution Non-commercial No Derivatives.

Download (3MB)

Abstract

The need for high-speed/high-precision machine tools is swiftly increasing in response to the growth of production technology that necessitates high- recision parts and high productivity. The influence of thermally induced errors in machine tools can have a much greater influence on the dimensional tolerances of the final products produced as compared to geometric and cutting force errors. Therefore, to maintain high accuracy of machine tool, it requires an accurate method of thermal error control or compensation using a detailed model.
The thermal errors of machine tools are induced by the propagation of heat through the structure of the machine due to excitation of internal and external heat sources such as belt drives, motors and bearings. There has been significant research effort to model thermal errors of machine tools in recent decades. The utilised techniques have proved their capabilities with excellent thermal prediction and compensation results but they often involve significant effort for effective implementation with constraints for complexity, robustness, and cost.
One of the most significant drawbacks of modelling machine behaviour using Finite Element Analysis (FEA) is the difficulty of accurately obtaining the characteristic of heat transfer, such as heat power of machine tool heat sources and the various boundary conditions.
The aims of this research to provide reliable techniques to obtain heat transfer coefficients of
machine tools in order to improve the accuracy of FEA simulations. FEA is used to simulate the thermal characteristics of spindle system of small Vertical Machining Centre (VMC) using SolidWorks Simulation software.
Most FEA models of machine tools employ the general prediction technique based on formulae, provided by OEMs, to identify many of the boundary conditions associated with simulating thermal error in machine tools. The formulae method was used to identify the heat transfer coefficients of a small VMC feed drive system. Employing these values allowed FEA to be used to simulate the thermal characteristics of the feed drive model. In addition, an alternative efficient methodology, based on energy balance calculations and thermal imaging, was used to obtain the heat transfer coefficients of the same feed drive system. Then the parameters obtained were applied to the FEA model of the system and validated against experimental results. The residual thermal error was reduced to just 20 % when the energy balance method was employed and compared with a residual of 30 %, when the formulae method was employed.
The existing energy balance method was also used to obtain the heat transfer coefficients of the headslide on a small VMC based on thermal imaging data. Then FEA model of the headslide of VMC was created and simulated. There was significant reduction in the thermal error but significant uncertainties in the method were identified suggesting that further improvements could be made.
An additional novel Two Dimensional (2D) optimisation technique based on thermal imaging data was created and used to calibrate the calculated heat transfer coefficients of the headslide of a small sized machine tool. In order to optimise the heat power of various heat sources, a 2D model of surface temperature of the headslide was created in Matlab software and compared against the experimental data both spatially across a plane and over time in order to take into account time varying heat loads. The effectiveness of the technique was proved using FEA models of the machine and comparison with test data from the machine tool. Significant improvement was achieved with correlation of 85 % between simulated thermal characteristics and the experimental data

Item Type: Thesis (Doctoral)
Subjects: T Technology > T Technology (General)
T Technology > TA Engineering (General). Civil engineering (General)
Schools: School of Computing and Engineering
Depositing User: Elizabeth Boulton
Date Deposited: 10 May 2016 13:59
Last Modified: 02 Dec 2016 04:29
URI: http://eprints.hud.ac.uk/id/eprint/28318

Downloads

Downloads per month over past year

Repository Staff Only: item control page

View Item View Item

University of Huddersfield, Queensgate, Huddersfield, HD1 3DH Copyright and Disclaimer All rights reserved ©